We are working on a seastead design.

The goal is to design our seastead such that all the parts can pack into a single a High Cube 45 foot container which has:
   width 7.7 ft
   height 8.9 ft
   length 44.6 ft
   max weight:  62,000 lbs  (rated bouyancy at desired waterline is 27,500 lbs and we hope structure is enough under this that humans and their stuff can fit)

Above the water there will be a big equilateral triangle frame, 44.0 feet on a side. 
The triangle frame is also the wall of the living area and will be 7 feet high (floor to ceiling).
It will be enclosed and the whole inside the living area.
Around the whole outside of the wall, except where the dinghy is in the back, will be a 3 foot wide walkway and railing that 
is bolted on and has some diagonal supports from below bracing to the wall (so walkway is 1 food higher than bottom of the wall).
The walkway will have an aluminum grating that would let a wave pass through but you can walk on.
Also two doors on the back side,  one two feet in from left and one two feet in from the right side. 

There are 3 legs/floats/foils/wings/keels that provide the buoyancy, so it is a bit like a trimaran but with a very soft ride.
Each leg/wing will 21.5 feet long and have a NACA 0035 foil shape with 8.5 foot chord except that the last 0.5 feet of
the thinnest part will be cut short, so with foil does not come to a point at the trailing edge and fits within 8.9 feet
hight of container.  But the buoyancy is very close to that of an 8.5 foot chord foil.
Each of the 3 legs will be attached to the underside of the big triangle near one of the 3 points.
The center of the thickest part and going 1.5 feet in all directions from there will be within the area of the triangle,
but within that constraint, each leg will be as close to the point of the triangle as possible.
The legs will go down so that the lower half is in the water.
This makes for a bit of "small waterline area" similar like a small oil platform but one that can move through the water easier because of the foil shape.
It is not an extreme SWATH design as a 1 foot change in water level is about 1/7th of the total buoyancy, so still significant change.
The 3 legs will all be parallel with the blunt or "leading edge of the wing" side facing forward so it is lower drag when moving forward
than a typical cylinder on a semi-submersible platform.  
Each leg will be 50% under the water (so 0.5 * 14.5 feet) and the top 50% out of the water.
On the top half of the front of each leg, so the top half that is out of the water, will be a built in ladder.

The reason for these sizes for the triangle and legs is so they can pack into a container nicely and shipped to 
a shipyard anywhere for assembly.
Two of the legs will be packaged together with one having the round edge down and pointy edge up and the 
other having the round edge up and pointy edge down so they are just over the thickness of the foil together
and loaded along the right wall all the way to the back.  
The 3rd leg will be along the right wall with the round side down between the first 2 and the container opening.
So the right few feet of the container (width of legs) is used by the 3 legs.
Then the 3 frame/wall sections will be upright (so 7 feet high) next to each other along the left side of the container.  
I am not sure the width of the walls but if they were 10 inches wide then 3 widths is 30 inches and some extra is 3 feet on the left side.
There should still be lots of room in the center of the container for all the other parts.

Connecting the mid points of the walls both at floor and ceiling level will be structural beams that
make another triangle 22 feet on a side.  Then all the remaining spans will be less than 22 feet.
The rest of the floor and ceiling will be small pieces that are bolted in.

On top of the roof there will be solar all over.  With batteries and electric thrusters as the main propulsion system.

There will be 6 RIM drive thrusters of 1.5 foot diameter, one on each side of the 3 legs/wings about 2 feet up from the bottom.
These RIM drives will be all be fixed orientation to provide forward thrust.  It will use differential thrust to turn.
For slow movements in tight areas like harbors it can reverse thrust on one side and forward on the other to turn in place.

There will be a conduit/pipe welded to the back of the trailing edge to take electrical wires down to the thrusters.
There will not be any "through hulls" in the legs.  The legs will also have multiple
airtight compartments each for safety.


Behind the back near the center will be two supports going out and 2 ropes going down to a dinghy.
The dinghy is a 14 foot RIB boat (deflated for shipping) with an electric Yamaha HARMO outboard.  It is sideways against the center of the backside of the living area.
When the seastead is moving forward the dingy is shielded from the wind by the living area.

On the lower part of each leg will be several bolt on heave plates.  These will help dampen the response to waves.

About 25% of the displacement will be for LiPo4 batteries which will be put low in the 3 legs.
Each leg will have its own charge controller and inverter so there is triple redundant power on the seastead.
Also, the thrusters for a leg will get power from that leg's inverter or batteries.  So
the 3 pairs of thrusters will have independent failure modes as far as power.

When the seastead is going to be staying in one place for awhile, we can put down 3 helical mooring screws and give the seastead tension legs 
so it becomes nearly stationary when parked.  Near each corner there will be a pair of helical mooring screws with a motor unit between them.
We only plan to do this in the Caribbean where tides are very small and in protected places where the saves are small,
so pulling down 3 feet will be sufficient to never go slack.


Two seasteads will be able to connect together with a walkway, one behind the other, so that while underway 
people can move between seasteads, enabling a real community.  The two computers for the two seastead will both work thrusters
to minimize the movement of the walkway, particularly when warned that someone will be on it.






Now I want to look at the possible impact of seastead life on couple birthrates.  
The hope is that some of these factors could help increase birthrates.

1) lower cost of home than in big cities, easier to start a family, can start sooner
2) less expenses for electricity, water, food
3) more sense of space and abundance when next house is 100 meters over than 1 meter over or above and below you
4) a feeling of controlling your own destiny as you can move to another country
5) being able to live in a country that is safe, low tax, and treats you well
6) not having to work multiple jobs to keep ahead of the bills
7) more optimism that your children will have a good life
8) healthier lifestyle & environment: Cleaner air, cleaner water, lower stress
9) pioneering community culture
10) a sense of being part of something new with potential
11) physical stability & mother's comfort: 
      many women on yachts don't want to get pregnant as they are afraid of falls but tension leg seastead is stable
12) work life integration - if you work from home taking care of kids may not seem such an issue
13) selection bias - the people who are adventurous enough to try out a new seastead lifestyle may
       just be more likely to be up for having children
14) friends and family close by - seasteaders who know each other can easily locate near to each other for easy support
         Might have grandparents seastead attached so they can help raise children
15) less time wasted on or stress from driving/commuting
16) feeling that this would be an ok life for a child to have
17) shielding from doom culture - not being in decaying urban centers with high crime has to improve 
             mental health and encourages family formation
18) if your friends are having children then you are more likely to as well
19) can increase home size by adding another seastead module so can cope with a growing family
20) like minded community of self sufficient people with shared interests 
21) no push for status symbols like fast cars
22) no painful delays from permits to build or waiting for inspections while building - get seastead home fast
23) low stress, easier finances, and comfortable living might reduce divorce rate and so increase family size
24) lots of free fresh fish in diet
25) natural light-dark cycle giving more regular sleep schedule 
26) reduced decision fatigue - fewer daily choices to make, simpler life you can cope with
27) The "Blue Mind" Effect: Proximity to water is scientifically proven to reduce stress
28) traveling with children can seem daunting enough that some couples may put off children to travel first 
          but with a seastead exploring new countries with children should be easier
29) avoiding the two income trap.  Many couples start with 2 incomes and transitioning to 1 becomes hard.
30) the exposure to nature of fishing, swimming, boating, sunlight, vitamin-D 
31) High-Trust Community Moats: Quite literally surrounded by a moat 
32) Extended "fertile window" from low-stress seastead lifestyle


Can you think of other factors?  Also factors that may reduce birthrates?

What have modern terrestrial homesteaders, intentional off-grid communities, highly religious groups,
home schoolers, or any other analogs that might be relevant,  had as birthrates?

Can you find any evidence that these would increase birthrates?

What sort of birthrate do you think seastead families might get?

Feel free to reorganize, group, add to, and combine or ignore above factors to make a presentation on
the issues.